The Flying Fish

3 findings recorded on Nov 10, 2026.

1. Violation recordedItem 4-2B ↗

   Food-contact surface sanitation

   Observed the 3 comp sink providing 0 ppm quaternary compound sanitizer. CA: Advised PIC to have the sanitizer line fixed to provide the appropriate concentration.

   Inspector’s full note

   Inspection item: Food-contact surfaces: cleaned & sanitized

   Code 511-6-1.05(6)(n)

   Observed the 3 comp sink providing 0 ppm quaternary compound sanitizer. CA: Advised PIC to have the sanitizer line fixed to provide the appropriate concentration. 511-6-1.05(6)(n) - Manual and Mechanical Warewashing Equipment, Chemical Sanitization-Temperature, pH, Concentration, Hardness (P,Pf) (n) Manual and Mechanical Warewashing Equipment, Chemical Sanitization - Temperature, pH, Concentration, and Hardness. A chemical sanitizer used in a sanitizing solution for a manual or mechanical operation at contact times specified under subsection (8)(b)3 of this Rule shall meet the requirements specified in DPH Rule 511-6-1-.07(6)(g), shall be used in accordance with the Environmental Protection Agency (EPA)-registered label use instructions P, and shall be used as follows: 1. A chlorine solution shall have a minimum temperature based on the concentration and pH of the solution as listed in the following chart; P Concentration Range Minimum Temperature MG/L PH 10 or less oF (oC) PH 8 or less oF (oC) 25-49 120 (49) 120 (49) 50-99 100 (38) 75 (24) 100 55 (13) 55 (13) 2. An iodine solution shall have a minimum temperature of 68°F (20°C)P minimum concentration between 12.5 ppm and 25 ppm, P and pH of 5.0 or less or a pH no higher than the level for which the manufacturer specifies for the solution to be effective; P 3. A quaternary ammonium compound solution shall have a minimum temperature of 75ºF (24ºC), P have a concentration as specified in DPH Rule 511-6-1-.07(6)(g) and as indicated by the manufacturer’s use directions included in the labeling, P and be used only in water with 500 ppm hardness or less or in water having a hardness no greater than specified by the EPA-registered label use instructions; P 4. If another solution of a chemical specified under paragraphs 1 through 3 of this subsection is used, the permit holder shall demonstrate to the Health Authority that the solution achieves sanitization and the use of the solution shall be approved; P 5. If a chemical sanitizer other than chlorine, iodine, or a quaternary ammonium compound is used, it shall be applied in accordance with the EPA-registered label use instructions ;P and 6. If a chemical sanitizer is generated by a device located on-site at the food service establishment, it shall be used as specified in 1-5 of this subsection and shall be produced by a device that: (i) complies with law as specified in sections 2(q)(1) and 12 of the Federal Insecticide, Fungicide, and Rodenticide Act (FIFRA), P (ii) complies with 40 CFR 152.500 Requirement for Devices and 40 CFR 156.10 Labeling Requirements, P (iii) displays the EPA device manufacturing facility registration number on the device, Pf and (iv) is operated and maintained in accordance with manufacturer’s instructions. Pf. 7. On-site chemical sanitizer generating equipment with active ingredients, such as copper, must be registered as pesticides. The active ingredient may be part of the equipment or separately added. New Violation. Correct By: 11/13/2026

   Official report · Item 4-2B ↗

   Correction status not recorded

   Correct by Nov 13, 2026

2. Violation recordedItem 15A ↗

   Equipment design and condition

   Observed the facility WIC not fully sealed at the base to allow for continuous refrigeration. CA: Advised PIC to maintain the WIC in good repair.

   Inspector’s full note

   Inspection item: Food and nonfood-contact surfaces cleanable, properly designed, constructed, and used

   Code 511-6-1.05(6)(a)

   Observed the facility WIC not fully sealed at the base to allow for continuous refrigeration. CA: Advised PIC to maintain the WIC in good repair. 511-6-1.05(6)(a) - Good Repair & Proper Adjustment (C) (6) Maintenance and Operation. (a) Good Repair and Proper Adjustment. 1. Equipment shall be maintained in a state of repair and condition that meets the requirements specified under subsections (1) and (2)of this Rule. 2. Equipment components such as doors, seals, hinges, fasteners, and kick plates shall be kept intact, tight, and adjusted in accordance with manufacturer's specifications. 3. Cutting or piercing parts of can openers shall be kept sharp to minimize the creation of metal fragments that can contaminate food when the container is opened. New Violation.

   Official report · Item 15A ↗

   Correction status not recorded

3. Violation recordedItem 18 ↗

   Pest control

   Observed multiple areas of the food stall with small flies. CA: Advised PIC to have sufficient enough pest control to manage their presence.

   Inspector’s full note

   Inspection item: Insects, rodents, and animals not present

   Code 511-6-1.07(5)(k)

   Observed multiple areas of the food stall with small flies. CA: Advised PIC to have sufficient enough pest control to manage their presence. 511-6-1.07(5)(k) - Controlling Pests (Pf, C) (k) Controlling Pests. The presence of insects, rodents, and other pests shall be controlled to minimize their presence on the premises by: 1. Routinely inspecting incoming shipments of food and supplies; 2. Routinely inspecting the premises for evidence of pests; 3. Using methods, if pests are found, such as trapping devices or other means of pest control as specified under subsections (6)(e), (6)(m), and (6)(n) of this Rule; Pf and 4. Eliminating harborage conditions. New Violation. Correct By: 11/20/2026

   Official report · Item 18 ↗

   Correction status not recorded

   Correct by Nov 20, 2026

Correction status comes from the dated report. Later changes may not be recorded here.